Specifications
Engine
- Engine Model
- Cat C32B
- Gross Power
- 907hp
- Emissions (U.S. EPA Tier 4 Final): Gross Power - SAE J1995
- 900hp
- Emissions (U.S. EPA Tier 4 Final): Net Power ISO - 9249
- 814hp
- Emissions (Tier 2 Equivalent): Gross Power - SAE J1995
- 907hp
- Emissions (Tier 2 Equivalent): Net Power ISO - 9249
- 823hp
- Rated Speed
- 1750r/min
- Bore
- 5.7in
- Stroke
- 6.4in
- Displacement
- 1958in²
- Peak Torque - 1,200 rpm
- 3139lb/ft
- Torque Rise
- 30%
- Note (1)
- Net power advertised is the power available at the flywheel when the engine is equipped with fan, air cleaner, muffler and alternator.
- Note (2)
- Net torque rise meets SAE J139.
- Note (3)
- No engine derating required up to 3050 m (10,000 ft) altitude.
Weights
- Operating Weight
- 224647lb
Transmission
- Transmission Type
- Cat Planetary Power Shift
- Converter Drive - Forward 1
- 4.4mile/h
- Converter Drive - Forward 2
- 7.7mile/h
- Converter Drive - Forward 3
- 13.2mile/h
- Converter Drive - Reverse 1
- 4.8mile/h
- Converter Drive - Reverse 2
- 8.4mile/h
- Converter Drive - Reverse 3
- 14.6mile/h
- Direct Drive - Forward 1
- Lock-up disabled
- Direct Drive - Forward 2
- 8.1mile/h
- Direct Drive - Forward 3
- 14.2mile/h
- Direct Drive - Reverse 1
- 5mile/h
- Direct Drive - Reverse 2
- 8.9mile/h
- Direct Drive - Reverse 3
- 15.6mile/h
- Note
- Travel speeds based on 45/65-45 L-5 46 ply tires.
Hydraulic System - Lift/Tilt
- Output at 1,850 rpm and 6900 kPa (1,000 psi)
- 161gal/min
- Cylinders, Double Acting - Lift, Bore and Stroke
- 177 mm × 1760 mm (0.58 ft × 5.8 ft)
- Cylinder, Double Acting - Tilt and Tip, Bore and Stroke
- 267 mm × 286 mm (0.88 ft × 0.94 ft)
Service Refill Capacities
- Fuel Tank - Standard
- 413gal (US)
- Cooling System
- 53gal (US)
- Crankcase
- 32gal (US)
- Transmission
- 45gal (US)
- Differential - Final Drives - Front
- 98gal (US)
- Differential - Final Drives - Rear
- 90gal (US)
- Hydraulic System - Steering and Engine Cooling Fan - Tank Only
- 77gal (US)
- Note (1)
- - All nonroad U.S. EPA Tier 4, European Union (EU) Stage IIIB and V, and Japan (MLIT) Step 4 diesel engines are required to use only Ultra Low Sulfer Diesel (ULSD) fuels containing 15 ppm (mg/kg) sulfer or less. Biodiesel blends up to B20 (20% blend by vo
Axles
- Front
- Fixed
- Rear
- Trunnion
Brakes
- Brakes
- Meets ISO 3540:2011
Blades
- Blade Capacities
- 30.5 to 44.8 m3 (40 to 58.6 yd3)
Dimensions (Approximate)
- Height - Top of ROPS
- 18.25ft
- Height - Top of Exhaust Pipe
- 17.17ft
- Height - Top of Hood
- 13ft
- Ground Clearance
- 27in
- Centerline of Front Axle to Hitch
- 9.67ft
- Centerline of Rear Axle to Edge of Bumper
- 13.75ft
- Wheel Base
- 19.25ft
- Length - With Blade on Ground
- 44ft
Hydraulic System - Steering
- Steering System - Pump
- Piston, variable displacement
- Minimum Turning Radius - Over Blade
- 31ft
- Steering System - Circuit
- Pilot, load sensing
- Total Steering Angle
- 86 degrees
- Relief Valve Setting
- 5004psi
Operating Specifications
- Operating Weight
- 224647lb
Sound Performance Levels
- Sound Performance
- • The machine sound power level was measured according to ISO 6395:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed. • The operator sound pressure level was measured according to ISO 6396:2008. The measurement was
Air Conditioning System
- Air Conditioning
- The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.8 kg of refrigerant which has a CO2 equivalent of 2.574 metric tonnes.
Cab
- ROPS/FOPS
- ISO 3471:2008 and ISO 3449:2005 Level II Standards